PU INJECTION GROUT

Price on Request: Get Latest Price

Next generation, phthalate free, closed cell, 1-component, high performance, low viscosity, hydrophobic, HydroActive, rigid polyurethane injection grout for cutting off gushing water leaks with a high flow rate and/or high hydrostatic pressure.

• Additional Information

  field of application:
  • Designed for cutting off gushing water leaks with a high flow rate and/or
  high pressure.
  • Used to block water leaks in diaphragm walls.
  • Filling large voidssuch asrock fissures, crushed faults, gravel layers, joints,
  cracks and honeycombs in concrete structures that are not subject to settlement or movement.
  • Injection of LDPE or HDPE membranes in tunnel construction.
  • Pre-injections for waterproofing and consolidation in front of the TBM,
  with drill-and-blast and NATM under wet condition.
  • In combination with cement and micro-fine cement for Combi-Grouting.
  • For tie-back and screw rod anchoring in wet and dry conditions.
  • For curtain injection into gravel for containing chemicals under wet or dry
  conditions.
  • For soil stabilisation and anchoring in gravel.
  • For screen injection behind porous structures when high velocity water
  streams are present.
  
  Advantages:
  
  
  • ADR free transport.
  • Next generation resin with improved waterproofing performance.
  • Improved cell structure of the cured compound resulting in better mechanical properties and durability.
  • Phthalate free resins, REACH compliant.
  • Improved performance at temperatures below 5°C, no crystallisation of
  HA Cut Cat AF.
  • Fast, Extra-Fast and Super Extra-Fast catalysts available for applications
  where the standard catalyst reaction speed is insufficient due to low temperatures or very high water flow. (See respective Technical Data Sheet)
  • HA Cut AF forms a rigid gasket with high strength in the joint or crack.
  • Non-flammable, solvent free.
  • User friendly: 1-component material.
  • Controllable reaction times: by using catalyst curing times can be reduced.
  • Cured compound is resistant to most organic solvents, mild acids, alkalis
  and microorganisms.(*)
  • KTW Potable Water approved.

Price on Request: Get Latest Price

TamPur 130 / TamKat 130 is a single-shot hydrophobic polyurethane based on MDI in combination with polyether polyols and an amine based catalyst. The system only reacts when it comes into contact with water, producing a semi-flexible polyurethane foam.

• Additional Information

  KEY BENEFITS
  • Potable water approved & PUB Singapore approved
  • Can withstand high hydrostatic pressures
  • Variable reaction times
  • Semi-flexible Reacts with saline and mineral water
  • Medium viscosity Solvent free,
  • Environmentally safe
  
  TYPICAL APPLICATIONS
  • Sealing against water ingress
  • Sealing against leaking cracks and joints
  • Sealing against water in masonry and brickwork
  • Back grouting

Price on Request: Get Latest Price

Tampur 125 is based on a polyol component (part A) and a polymeric MDI (part B). When mixed, a hydrophobic polyurethane foam is formed which is tough, rigid and resistant to a wide range of chemicals. TamPur 125 reacts rapidly enabling the product to cut off large water leaks.

• Additional Information

  KEY BENEFITS
  
  High foam strength
  Rapid reaction
  Good bond strength
  Medium viscosity
  Solvent free, environmentally safe.
  
  Typical application
  • Extreme water ingress
  • Large voids
  • Dry fissure grouting
  • Foundation stabilisation

Price on Request: Get Latest Price

Tampur 136 is a single component hydrophobic polyurethane based on MDI in combination with polyether polyols. The system incorporates an active accelerator and only reacts when it comes into contact with water, producing a non-toxic, semi-flexible polyurethane foam.

• Additional Information

  KEY BENEFITS
  • Environmentally safe,
  • non-toxic
  • In built accelerator
  • Semi-flexible Reacts with saline and mineral water
  • Low viscosity
  
  TYPICAL APPLICATIONS
  
  • Sealing against water ingress
  • Sealing against leaking cracks and joints
  • Sealing against water in masonry and brickwork
  • Back grouting

Price on Request: Get Latest Price

CYH-500 is a hydrophobic grout based on polyurethane.
Upon contact with water, CYH-500 reacts to closed cell rubber-like foam while expanding its volume up to 27 times. The cured material is of a constant volume. Since water is not a component of the foam structure, the cured material is essentially not affected by water or dryness. The reacted material does not shrink or swell. Depending on the pressure of injection, CYH-500 reacts to a very dense material or foam

• Additional Information

  Areas of application include:
  • Defective concrete (cracked or honeycombed)
  • Concrete joints, Limestone, Brick construction
  • Pipe intrusions, Waste water tanks
  • Tunnels, Dams, Subway(Metro), Sewers, Manholes, Utility boxes, etc.
  • Soil stabilization
  
  
  Advantages:
  • Negative side application possible
  
  • Deep penetration into very small cracks
  
  • Foam increases in volume to fill cavities and voids
  
  • Excellent bond to surfaces
  
  • Good adhesive strength, tolerant of movement
  
  • Inert after curing, constant volume, no shrinkage
  
  • Does not create new cracks

Price on Request: Get Latest Price

We are prominent supplier of a gamut of Building and Construction Material. The most acclaimed products are Concrete Fibers, Cellulose Fibers and Floor Hardeners. Our range is wide and comprehensive and appreciated for being exceptional in quality and durability. It is extensively used in building infrastructures, repairing work of structures, printing and painting industries

Price on Request: Get Latest Price

Phthalate-free, flexible, hydrophilic, low-viscous polyurethane resin for sealing moving, non-structural cracks

• Additional Information

  Use
  • For sealing damp, moving, non-structural cracks below groundwater level
  • For sealing water leaks through the joints of concrete tunnel elements
  • For screen injections behind tunnel segments
  • For sealing moving, leaking cracks
  • For filling gravel nests below groundwater level
  • For waterproofing man-accessible and non-man-accessible sewers
  • For expansion joints or round joints in combination with oil-free hemp cord or open-cell foam
  
  Product Description
  HA Safefoam NF is a phthalate-free, 1-component low-viscosity, hydrophilic polyurethane resin. After curing, HA Safefoam NF forms an inert, flexible foam with closed cell structure and very good tensile strength and adhesion. HA Safefoam NF can be used as a 2-component system with a ratio with water of 1/1 for the injection of dry cracks.
  Benefits
  • ADR free transport
  • Phthalate-free resin, REACH compliant
  • Solvent-free
  • TDI free
  • Not flammable
  • Very good adhesion and tensile strength
  • Withstands thermal movements, wet / dry cycles, freeze / thaw cycles and joint movements without degradation of the material.
  • Good general chemical resistance. (*)

Price on Request: Get Latest Price

Phthalate-free, fast-acting, 2-part, pre-catalyzed, rigid foam polyurethane injection system for structural injections requiring high compressive strength
RockStab resins are phthalate-free, 2-component injection resins consisting of a resin and a hardener that are pumped in a 1/1 mix ratio. After mixing the two components in a 1/1 ratio through a special mixing head with static mixer, the resin hardens into a hard foam, a very hard foam, or a hard plastic, depending on the type of Rockstab used.
Faster response times can be obtained by using an optional accelerator.

• Additional Information

  Rockstab is supplied in a 2-component set:
  • A-part: polyol blend
  • B component: isocyanate
  • Mixing ratio: 1/1 volumetrically
  
  Use
  • Filling of large voids, cracks and fractures
  • Consolidate rock formations
  • Grouting of injection anchors
  • Fastening rock bolts and rock anchors
  
  Benefits
  • ADR free transport
  • Phthalate-free resin, REACH compliant.
  • Solvent-free
  • Choice of different expansion ratios and compressive strengths
  • User-friendly: simple mixing ratio 1/1 (5% deviation is allowed)
  • Response and cure times can be easily controlled using an optional accelerator.

Price on Request: Get Latest Price

X-Inject WS100 is a two part Base (Part A) and Catalyst
(Part B) solvent-free, low viscosity, foaming
polyurethane resin system. When in contact with water
it reacts to form a rapidly expanding stable foam that
stops water leaks.
X-Inject WS100 is formulated to temporarily seal water
leaks in concrete structures to allow injection of a
secondary permanent seal using X-Inject PU211 or
PU221.

• Additional Information

  Advantages
  • Variable mixing ratios to control degree of foaming
  • Formulated for hot and cold climates
  • Can be supplied as a pre-catalysed single component
  product
  • Good adhesion to substrate
  • Withstands high hydrostatic pressures
  • Stable foam when cured
  • Application with electric or pneumatic injection pumps
  • Cured resin is non toxic
  • Suitable for use in contact with potable and brackish
  
  Uses
  • Rapid sealing of leaking cracks in concrete structures.